Error Codes for IPSO
IPSO is a renowned name in the commercial laundry sector, manufacturing a variety of washing machines and dryers. These machines come with diagnostic systems that indicate error codes to notify users of any potential issues that require attention. It is crucial to comprehend these error codes to troubleshoot and maintain the optimal performance of your IPSO laundry equipment.
If the error codes persist or you encounter a code that is not listed here, it's advisable to consult with one of our professional technicians. They can provide more specific guidance and perform necessary repairs if needed.
Need assistance?
Call us now on 0115 961 3720 to book an engineer. We’re always here to help
List of IPSO Error Codes
Model: M20/M9
| Error Code | Error |
| \"------------\" | BOARD RESETTING,CUTOUT ON SPIN ? CHECK DOOR HANDLE/LOCK |
| E4 | WATER LEVEL NOT REACHED WITHIN 15MINS, WATER PRESSURE/DRAIN VAL |
| E5 | TEMP NOT REACHED WITHIN 80 MINS |
| E6 | DOOR UNLOCKED DURING WASH,FAULTY DOOR HANDLE/LOCK |
| E7 | WATER DIDN’T DRAIN TO ALLOW SPIN, DRAIN VAL OR BLOCKAGE |
| E8 | TEMPERATURE BELOW 5C OR ABOVE 95C FAULTY TEMPSENSOR TM140/204 |
| EA | TILT SWITCH ACTIVATED 15 TIMES, OUT OF BALANCE LOADING SHOCKERS DRAINAGE |
| Eb | TILT SWITCH BLOCKED FAULTY |
Model: M20
| Error Code | Error |
| E3 | EPROM ERROR INCORRECT CHIP OR FAULTY BOARD |
| E9 | MOTOR THERMAL PROTECTOR TRIGGERED |
| END | DOOR FAILED TO OPEN,HANDLE/MECH OR SWITCHES |
| NOT2 | SPEED ERROR CHECK WIRING IF PLUG IS FITTED/ SPEED SENSOR F7MAIN PULLEY LOOSE?TM215 |
| NO DISPLAY | CHECK DOOR LOCK HANDLE(DOOR LOCK MAYBE STUCK) THE DOOR MAYNOT OPEN !!!!!!!!!!!!!!! |
Model: ALL
| Error Code | Error |
| CLOSE | DOOR FAILED TO LOCK,HANDLE/MECH OR SWITCHES |
Model: SIGMA
| Error Code | Error |
| OFF ECHO | FAILED THERMAL CYCLE, ENTER CODE AS FOLLOWS = PEPI SELECT(P) ECONOMY(E) SELECT (P) START ( I ) |
Model: PLC9
| Error Code | Error |
| 1tE/2tE | REQD TEMP WASN’T REACHED |
| 3tE | REQD TEMP WASN’T REACHED |
| cdo | DOOR NOT CLOSED,INSPECT DOOR LOCK/HANDLE |
| 4tE | REQD TEMP WASN’T REACHED |
| E9 | MOTOR TOC ACTIVATED |
| HLE at start | AT THE START WATER LEVEL SWITCH FAULT HLE = HIGH LEVEL LLE LOW LEVELOR SLE-TILT |
| HLE during wash | WATER LEVEL NOT REACHED (HLE HIGH LEVEL) ( LLE LOW LEVEL) |
| SLE at start | LEVEL SWITCH MAY BE FAULTY/AIR DOME BLOCKED |
| SLE-tilt | WATER LEVEL NOT REACHED |
Model: PC30
| Error Code | Error |
| Error=04 | FILLING TIME LONGER THAN 15MINS |
| Error=05 | TEMP NOT REACHED WITHIN 60 MINS |
| Error=06 | DOOR LOCK RELEASED DURING THE PROGRAM |
| Error=07 | WATER IN THE TUB AFTER THE PROGRAM |
| Error=08 | TEMP SENSOR FAILURE OR TEMP OUT OF RANGE |
| Error=09 | THERMO-MAGNETIC PROTECTION WAS ACTIVATED |
| Error=10 | TILT SWITCH WAS ACTIVATED |
| Error=11 | WATER STILL IN DRUM AT START OF PROGRAM |
| Error=12 | WATER STILL IN DRUM 3MINS AFTER DRAIN,HEATING NOT ACTIVATED |
| Error=13 | REMOVE MOTOR WIRING IF INVERTER STILL ALARMS (INVERTER FAULTY) |
Model: PS40
| Error Code | Error |
| A2 | UNKNOWN PROGRAM SELECTED |
| A4 | FILLING TIME LONGER THAN 15MINS |
| A5 | TEMP NOT REACHED WITHIN 60 MINS |
| A6 | DOOR LOCK RELEASED DURING THE PROGRAM |
| A7 | WATER IN THE TUB AFTER THE PROGRAM |
| A8 | TEMP SENSOR FAILURE OR TEMP OUT OF RANGE |
| A9 | THERMO-MAGNETIC PROTECTION WAS ACTIVATED,NON INVERTER M/C'S ONLY |
| Ab | WATER STILL IN DRUM AT START OF PROGRAM |
| Ac | WATER NOT DRAINED WITHIN 3MIN'S,THERE WAS NO FURTHER HEATING |
| Ad | NO RPM MEASURED DURING THE SPIN,INVERTER M/C'S ONLY |
| AH | TILT'S PREVENTED SPIN |
| F5 | THE DOOR WAS OPEN DURING THE PROGRAM |
| F6 | THE DOOR WAS UNLOCKED DURING THE PROGRAM |
| FA | TILT SWITCH BLOCKED |
Model: 6000
| Error Code | Error |
| E9 | MOTOR OVERLOAD CURRENT (DRAWN ABOVE 8AMP FOR 6000) |
| E9 | TRIAC ON MOTOR BOARD MUST BE BTB NOT BTA |
| NOT 3 | 5000 HRS ,CARBON BRUSHES REQD |
| NOT1/ \"OOO\" | MOTOR OVERLOAD/MOTOR BOARD |
| NOT2 | TACHO FAULT ON MOTOR,CHECK CIRCUIT |
| NOT2 /\"OOO\" | SPEED ERROR,CHECK MOTOR BOARD/WIRING |
Model: DIRONER
| Error Code | Error |
| HEAT | TEMP BELOW 4oC OR ABOVE 190oC |
| NO AIR | AIR FLOW SWITCH NOT O/C |
| NO HEAT | HEAT NOT DETECTED 10SEC'S AFTER IT WAS ACTIVATED |
| NO SPEED | SPEED DETECTOR NOT SENDING SIGNAL FOR SPEED |
Still struggling with your IPSO machine's error code?
Call us now on 0115 961 3720 to book an engineer. We’re always here to help